Matching
|
|
|
Match the screwdriver tips illustrated below with their identifying letters.
Write the letter in the space provided.

|
|
1.
|
Torx
|
|
2.
|
Standard
|
|
3.
|
Square
|
|
4.
|
Phillips
|
|
5.
|
Hex
|
|
|
Match the following terms and identifying phrases. A. | Wrench opening completely surrounds the bolt head or nut. | B. | Box-like and made to
fit many types of handles. | C. | Clamping device used to hold and position
material while it is worked. | D. | Will not rebound like other
hammers. | E. | Has a hardened striking face. | F. | Also known as slip-joint
pliers. | G. | Family of tools used for assembling and disassembling threaded
fasteners. | H. | Useful for cutting heavier wire and pins. | I. | Handy when space is
limited and for holding small work. | J. | Permits tightening a threaded fastener for
maximum holding power without danger of the fastener failing. | K. | Has flattened
wedge-shaped blade. | L. | Double ended with two different size
openings. | M. | Can be adjusted to fit different size bolt heads and nuts. | N. | Wrench with one open
end and one box end. | O. | Wrench used to grip round
stock. | P. | Used with socket head fasteners. | Q. | Has X-shaped tip. | R. | Designed to cut
flush with work surface. | S. | Designed to turn flush- and recessed-type
threaded fasteners. |
|
|
6.
|
Vise
|
|
7.
|
Combination pliers
|
|
8.
|
Needle nose pliers
|
|
9.
|
Diagonal pliers
|
|
10.
|
Wrenches
|
|
11.
|
Torque-limiting wrench
|
|
12.
|
Adjustable wrench
|
|
13.
|
Open end wrench
|
|
14.
|
Box wrench
|
|
15.
|
Combination wrench
|
|
16.
|
Socket wrench
|
|
17.
|
Allen wrench
|
|
18.
|
Spanner wrench
|
|
19.
|
Pipe wrench
|
|
20.
|
Standard screwdriver
|
|
21.
|
Phillips screwdriver
|
|
22.
|
Ball-peen hammer
|
|
23.
|
Dead blow hammer
|
|
|
Match the following terms and identifying phrases. A. | Used where safety requirements require a shatterproof blade. | B. | Capable of producing
very accurate cuts. | C. | Cuts with a back-and-forth
motion. | D. | Used to cut most metals. | E. | Melts its way through
metal. | F. | Caused by worn blade. | G. | Cuts in only one direction. | H. | Can cut hardened
steel without having to anneal it. | I. | Best for cutting most nonferrous
metals. |
|
|
24.
|
Horizontal band saw
|
|
25.
|
Abrasive cutoff saw
|
|
26.
|
Cold circular saw
|
|
27.
|
Friction cutoff saw
|
|
28.
|
Skip tooth blade pattern
|
|
29.
|
Flexible-back blade
|
|
30.
|
Crooked cutting
|
Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
31.
|
Torque-limiting wrenches are used when ____.
A. | they fit the fastener better than another wrench | B. | a threaded fastener
must be tightened to specified limits | C. | no other available wrench will
fit | D. | None of the above. |
|
|
32.
|
A torque-limiting wrench will give an accurate reading when ____.
A. | the handle is lengthened slightly | B. | they are pushed or pulled | C. | the fastener stops
turning | D. | None of the above. |
|
|
33.
|
A wheel dresser is used on a grinding wheel to ____.
A. | check whether the wheel is running true | B. | true the wheel and
remove any glaze | C. | check concentricity of the wheel | D. | All of the
above. |
|
|
34.
|
A pipe wrench will grip round work, however, ____.
A. | it must be pushed instead of pulled like an adjustable wrench | B. | the jaws will mar
the work | C. | it is not available in a large range of sizes | D. | None of the
above. |
|
|
35.
|
When sawing, three or more teeth should be cutting at all times; otherwise
____.
A. | the teeth will straddle the section being cut and snap off | B. | greater pressure
will be required to make the blade cut | C. | the teeth will clog with
chips | D. | All of the above. |
|
|
36.
|
Tooth pattern determines the efficiency of a band saw blade in most materials.
The standard tooth pattern blade is best suited for cutting ____.
A. | nonmetallic materials | B. | most ferrous metals | C. | many nonferrous
metals | D. | All of the above. |
|
|
37.
|
____ is a natural abrasive.
A. | Silicon carbide | B. | Aluminum oxide | C. | Emery | D. | None of the
above. |
|
|
38.
|
The three-tooth rule for sawing means ____.
A. | at least three teeth per inch are in good condition | B. | the blade should be
adjusted every third rotation | C. | at least three teeth are in contact with the
work at all times during cutting | D. | All of the
above. |
|
|
39.
|
Plier size indicates the ____.
A. | overall length of the tool | B. | width of the gripping area | C. | maximum jaw
opening | D. | None of the above. |
|
|
40.
|
Tooth pattern determines the efficiency of a band saw blade in most materials.
The skip tooth pattern is best suited for cutting ____.
A. | nonmetallic materials | B. | most ferrous metals | C. | many nonferrous
metals | D. | All of the above. |
|
Completion Complete each
statement.
|
|
41.
|
Files should be cleaned with a(n) ______________________________, never your
hand.
|
|
42.
|
Moving the work across the wheel face can prevent the formation of
______________________________.
|
|
43.
|
The hacksaw cuts best at about ______________________________ strokes per
minute.
|
|
44.
|
External threads are cut with a(n) ______________________________.
|
|
45.
|
A reciprocating saw cuts on the ______________________________.
|
|
46.
|
Work is often held together with a(n) ______________________________ and/or
parallel clamp while being machined or worked on.
|
|
47.
|
With band-type power saws, the blade moves in ______________________________
direction(s).
|
|
48.
|
For best cutting action, apply ______________________________ feed pressure on
hard materials and large work.
|
|
49.
|
Light feed pressure should be used when cutting ______________________________
materials and work with small cross sections.
|
|
50.
|
Band saw blades are made with ______________________________ set teeth and wavy
set teeth.
|
|
51.
|
When a file is pushed lengthwise, straight ahead, or at a slight angle across
the work, the operation is called ______________________________ filing.
|
|
52.
|
Offhand grinding is usually done on work that does not require great
______________________________.
|
|
53.
|
The ______________________________ provides support while work is being
ground.
|
|
54.
|
If too much pressure is applied to force the work against the grinding wheel,
the metal will ______________________________ and become discolored.
|
|
55.
|
Carbide tipped lathe cutting tools are usually sharpened on a(n)
______________________________ grinder.
|
|
56.
|
Care must be taken when grinding edge tools because excessive heat buildup will
remove the ______________________________ and ruin the tool.
|
|
57.
|
A grinding wheel that is glazed or loaded with metal should be
______________________________ before being used.
|
|
58.
|
If a grinding operation is to be performed dry, all
______________________________ should be hooked up before starting.
|
|
59.
|
A Pozidriv screwdriver tip is similar to the ______________________________
screwdriver tip.
|
|
60.
|
Bench and pedestal grinders are used to do ______________________________
grinding.
|
Short Answer
|
|
61.
|
What is the best way to hold thin metal for hacksawing?
|
|
62.
|
When grinding, why should the work be moved back and forth across the wheel
face?
|
|
63.
|
Should stock size be larger or smaller in diameter when external threads are to
be cut on it?
|
|
64.
|
How is offhand grinding accomplished?
|
|
65.
|
When is a 6-tooth blade usually used?
|
|
66.
|
What are the four general types of cold chisels?
|
|
67.
|
Why does a horizontal band saw produce less waste?
|
|
68.
|
Why should the grinding of soft metals be avoided?
|
|
69.
|
List the causes of blade breakage in power sawing.
|
|
70.
|
What are some of the tasks of the grinding operation?
|